summaryrefslogtreecommitdiff
path: root/usbdrv
diff options
context:
space:
mode:
Diffstat (limited to 'usbdrv')
-rw-r--r--usbdrv/usbconfig.2.h384
-rw-r--r--usbdrv/usbconfig.2_.h235
-rw-r--r--usbdrv/usbconfig.2__.h49
-rw-r--r--usbdrv/usbconfig_.h280
-rw-r--r--usbdrv/usbconfig__.h105
5 files changed, 0 insertions, 1053 deletions
diff --git a/usbdrv/usbconfig.2.h b/usbdrv/usbconfig.2.h
deleted file mode 100644
index 48d4a93..0000000
--- a/usbdrv/usbconfig.2.h
+++ /dev/null
@@ -1,384 +0,0 @@
-/* Name: usbconfig.h
- * Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
- * Author: Christian Starkjohann
- * Creation Date: 2005-04-01
- * Tabsize: 4
- * Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
- * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- */
-
-#ifndef __usbconfig_h_included__
-#define __usbconfig_h_included__
-
-/*
-General Description:
-This file is an example configuration (with inline documentation) for the USB
-driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
-also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
-wire the lines to any other port, as long as D+ is also wired to INT0 (or any
-other hardware interrupt, as long as it is the highest level interrupt, see
-section at the end of this file).
-+ To create your own usbconfig.h file, copy this file to your project's
-+ firmware source directory) and rename it to "usbconfig.h".
-+ Then edit it accordingly.
-*/
-
-/* ---------------------------- Hardware Config ---------------------------- */
-
-#define USB_CFG_IOPORTNAME D
-/* This is the port where the USB bus is connected. When you configure it to
- * "B", the registers PORTB, PINB and DDRB will be used.
- */
-#define USB_CFG_DMINUS_BIT 3
-/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
- * This may be any bit in the port.
- */
-#define USB_CFG_DPLUS_BIT 2
-/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
- * This may be any bit in the port. Please note that D+ must also be connected
- * to interrupt pin INT0! [You can also use other interrupts, see section
- * "Optional MCU Description" below, or you can connect D- to the interrupt, as
- * it is required if you use the USB_COUNT_SOF feature. If you use D- for the
- * interrupt, the USB interrupt will also be triggered at Start-Of-Frame
- * markers every millisecond.]
- */
-#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
-/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
- * 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
- * require no crystal, they tolerate +/- 1% deviation from the nominal
- * frequency. All other rates require a precision of 2000 ppm and thus a
- * crystal!
- * Since F_CPU should be defined to your actual clock rate anyway, you should
- * not need to modify this setting.
- */
-#define USB_CFG_CHECK_CRC 0
-/* Define this to 1 if you want that the driver checks integrity of incoming
- * data packets (CRC checks). CRC checks cost quite a bit of code size and are
- * currently only available for 18 MHz crystal clock. You must choose
- * USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
- */
-
-/* ----------------------- Optional Hardware Config ------------------------ */
-
-/* #define USB_CFG_PULLUP_IOPORTNAME D */
-/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
- * V+, you can connect and disconnect the device from firmware by calling
- * the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
- * This constant defines the port on which the pullup resistor is connected.
- */
-/* #define USB_CFG_PULLUP_BIT 4 */
-/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
- * above) where the 1.5k pullup resistor is connected. See description
- * above for details.
- */
-
-/* --------------------------- Functional Range ---------------------------- */
-
-#define USB_CFG_HAVE_INTRIN_ENDPOINT 0
-/* Define this to 1 if you want to compile a version with two endpoints: The
- * default control endpoint 0 and an interrupt-in endpoint (any other endpoint
- * number).
- */
-#define USB_CFG_HAVE_INTRIN_ENDPOINT3 0
-/* Define this to 1 if you want to compile a version with three endpoints: The
- * default control endpoint 0, an interrupt-in endpoint 3 (or the number
- * configured below) and a catch-all default interrupt-in endpoint as above.
- * You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
- */
-#define USB_CFG_EP3_NUMBER 3
-/* If the so-called endpoint 3 is used, it can now be configured to any other
- * endpoint number (except 0) with this macro. Default if undefined is 3.
- */
-/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
-/* The above macro defines the startup condition for data toggling on the
- * interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
- * Since the token is toggled BEFORE sending any data, the first packet is
- * sent with the oposite value of this configuration!
- */
-#define USB_CFG_IMPLEMENT_HALT 0
-/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
- * for endpoint 1 (interrupt endpoint). Although you may not need this feature,
- * it is required by the standard. We have made it a config option because it
- * bloats the code considerably.
- */
-#define USB_CFG_SUPPRESS_INTR_CODE 0
-/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
- * want to send any data over them. If this macro is defined to 1, functions
- * usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
- * you need the interrupt-in endpoints in order to comply to an interface
- * (e.g. HID), but never want to send any data. This option saves a couple
- * of bytes in flash memory and the transmit buffers in RAM.
- */
-#define USB_CFG_INTR_POLL_INTERVAL 10
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
-#define USB_CFG_IS_SELF_POWERED 0
-/* Define this to 1 if the device has its own power supply. Set it to 0 if the
- * device is powered from the USB bus.
- */
-#define USB_CFG_MAX_BUS_POWER 50
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
-#define USB_CFG_IMPLEMENT_FN_WRITE 1
-/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
- * transfers. Set it to 0 if you don't need it and want to save a couple of
- * bytes.
- */
-#define USB_CFG_IMPLEMENT_FN_READ 0
-/* Set this to 1 if you need to send control replies which are generated
- * "on the fly" when usbFunctionRead() is called. If you only want to send
- * data from a static buffer, set it to 0 and return the data from
- * usbFunctionSetup(). This saves a couple of bytes.
- */
-#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
-/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
- * You must implement the function usbFunctionWriteOut() which receives all
- * interrupt/bulk data sent to any endpoint other than 0. The endpoint number
- * can be found in 'usbRxToken'.
- */
-#define USB_CFG_HAVE_FLOWCONTROL 0
-/* Define this to 1 if you want flowcontrol over USB data. See the definition
- * of the macros usbDisableAllRequests() and usbEnableAllRequests() in
- * usbdrv.h.
- */
-#define USB_CFG_DRIVER_FLASH_PAGE 0
-/* If the device has more than 64 kBytes of flash, define this to the 64 k page
- * where the driver's constants (descriptors) are located. Or in other words:
- * Define this to 1 for boot loaders on the ATMega128.
- */
-#define USB_CFG_LONG_TRANSFERS 0
-/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
- * in a single control-in or control-out transfer. Note that the capability
- * for long transfers increases the driver size.
- */
-/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
-/* This macro is a hook if you want to do unconventional things. If it is
- * defined, it's inserted at the beginning of received message processing.
- * If you eat the received message and don't want default processing to
- * proceed, do a return after doing your things. One possible application
- * (besides debugging) is to flash a status LED on each packet.
- */
-/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
-/* This macro is a hook if you need to know when an USB RESET occurs. It has
- * one parameter which distinguishes between the start of RESET state and its
- * end.
- */
-/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
-/* This macro (if defined) is executed when a USB SET_ADDRESS request was
- * received.
- */
-#define USB_COUNT_SOF 0
-/* define this macro to 1 if you need the global variable "usbSofCount" which
- * counts SOF packets. This feature requires that the hardware interrupt is
- * connected to D- instead of D+.
- */
-/* #ifdef __ASSEMBLER__
- * macro myAssemblerMacro
- * in YL, TCNT0
- * sts timer0Snapshot, YL
- * endm
- * #endif
- * #define USB_SOF_HOOK myAssemblerMacro
- * This macro (if defined) is executed in the assembler module when a
- * Start Of Frame condition is detected. It is recommended to define it to
- * the name of an assembler macro which is defined here as well so that more
- * than one assembler instruction can be used. The macro may use the register
- * YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
- * immediately after an SOF pulse may be lost and must be retried by the host.
- * What can you do with this hook? Since the SOF signal occurs exactly every
- * 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
- * designs running on the internal RC oscillator.
- * Please note that Start Of Frame detection works only if D- is wired to the
- * interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
- */
-#define USB_CFG_CHECK_DATA_TOGGLING 0
-/* define this macro to 1 if you want to filter out duplicate data packets
- * sent by the host. Duplicates occur only as a consequence of communication
- * errors, when the host does not receive an ACK. Please note that you need to
- * implement the filtering yourself in usbFunctionWriteOut() and
- * usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
- * for each control- and out-endpoint to check for duplicate packets.
- */
-#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
-/* define this macro to 1 if you want the function usbMeasureFrameLength()
- * compiled in. This function can be used to calibrate the AVR's RC oscillator.
- */
-#define USB_USE_FAST_CRC 0
-/* The assembler module has two implementations for the CRC algorithm. One is
- * faster, the other is smaller. This CRC routine is only used for transmitted
- * messages where timing is not critical. The faster routine needs 31 cycles
- * per byte while the smaller one needs 61 to 69 cycles. The faster routine
- * may be worth the 32 bytes bigger code size if you transmit lots of data and
- * run the AVR close to its limit.
- */
-
-/* -------------------------- Device Description --------------------------- */
-
-#define USB_CFG_VENDOR_ID 0xc0, 0x16 /* = 0x16c0 = 5824 = voti.nl */
-/* USB vendor ID for the device, low byte first. If you have registered your
- * own Vendor ID, define it here. Otherwise you may use one of obdev's free
- * shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
- * *** IMPORTANT NOTE ***
- * This template uses obdev's shared VID/PID pair for Vendor Class devices
- * with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
- * the implications!
- */
-#define USB_CFG_DEVICE_ID 0xdc, 0x05 /* = 0x05dc = 1500 */
-/* This is the ID of the product, low byte first. It is interpreted in the
- * scope of the vendor ID. If you have registered your own VID with usb.org
- * or if you have licensed a PID from somebody else, define it here. Otherwise
- * you may use one of obdev's free shared VID/PID pairs. See the file
- * USB-IDs-for-free.txt for details!
- * *** IMPORTANT NOTE ***
- * This template uses obdev's shared VID/PID pair for Vendor Class devices
- * with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
- * the implications!
- */
-#define USB_CFG_DEVICE_VERSION 0x00, 0x01
-/* Version number of the device: Minor number first, then major number.
- */
-#define USB_CFG_VENDOR_NAME 'w','i','n','d','f','i','s','c','h','.','o','r','g'
-#define USB_CFG_VENDOR_NAME_LEN 13
-/* These two values define the vendor name returned by the USB device. The name
- * must be given as a list of characters under single quotes. The characters
- * are interpreted as Unicode (UTF-16) entities.
- * If you don't want a vendor name string, undefine these macros.
- * ALWAYS define a vendor name containing your Internet domain name if you use
- * obdev's free shared VID/PID pair. See the file USB-IDs-for-free.txt for
- * details.
- */
-#define USB_CFG_DEVICE_NAME 'F','l','o',' ','T','e','s','t'
-#define USB_CFG_DEVICE_NAME_LEN 8
-/* Same as above for the device name. If you don't want a device name, undefine
- * the macros. See the file USB-IDs-for-free.txt before you assign a name if
- * you use a shared VID/PID.
- */
-/*#define USB_CFG_SERIAL_NUMBER 'N', 'o', 'n', 'e' */
-/*#define USB_CFG_SERIAL_NUMBER_LEN 0 */
-/* Same as above for the serial number. If you don't want a serial number,
- * undefine the macros.
- * It may be useful to provide the serial number through other means than at
- * compile time. See the section about descriptor properties below for how
- * to fine tune control over USB descriptors such as the string descriptor
- * for the serial number.
- */
-#define USB_CFG_DEVICE_CLASS 0xff /* set to 0 if deferred to interface */
-#define USB_CFG_DEVICE_SUBCLASS 0
-/* See USB specification if you want to conform to an existing device class.
- * Class 0xff is "vendor specific".
- */
-#define USB_CFG_INTERFACE_CLASS 0 /* define class here if not at device level */
-#define USB_CFG_INTERFACE_SUBCLASS 0
-#define USB_CFG_INTERFACE_PROTOCOL 0
-/* See USB specification if you want to conform to an existing device class or
- * protocol. The following classes must be set at interface level:
- * HID class is 3, no subclass and protocol required (but may be useful!)
- * CDC class is 2, use subclass 2 and protocol 1 for ACM
- */
-/* #define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 42 */
-/* Define this to the length of the HID report descriptor, if you implement
- * an HID device. Otherwise don't define it or define it to 0.
- * If you use this define, you must add a PROGMEM character array named
- * "usbHidReportDescriptor" to your code which contains the report descriptor.
- * Don't forget to keep the array and this define in sync!
- */
-
-/* #define USB_PUBLIC static */
-/* Use the define above if you #include usbdrv.c instead of linking against it.
- * This technique saves a couple of bytes in flash memory.
- */
-
-/* ------------------- Fine Control over USB Descriptors ------------------- */
-/* If you don't want to use the driver's default USB descriptors, you can
- * provide our own. These can be provided as (1) fixed length static data in
- * flash memory, (2) fixed length static data in RAM or (3) dynamically at
- * runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
- * information about this function.
- * Descriptor handling is configured through the descriptor's properties. If
- * no properties are defined or if they are 0, the default descriptor is used.
- * Possible properties are:
- * + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
- * at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
- * used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
- * you want RAM pointers.
- * + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
- * in static memory is in RAM, not in flash memory.
- * + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
- * the driver must know the descriptor's length. The descriptor itself is
- * found at the address of a well known identifier (see below).
- * List of static descriptor names (must be declared PROGMEM if in flash):
- * char usbDescriptorDevice[];
- * char usbDescriptorConfiguration[];
- * char usbDescriptorHidReport[];
- * char usbDescriptorString0[];
- * int usbDescriptorStringVendor[];
- * int usbDescriptorStringDevice[];
- * int usbDescriptorStringSerialNumber[];
- * Other descriptors can't be provided statically, they must be provided
- * dynamically at runtime.
- *
- * Descriptor properties are or-ed or added together, e.g.:
- * #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
- *
- * The following descriptors are defined:
- * USB_CFG_DESCR_PROPS_DEVICE
- * USB_CFG_DESCR_PROPS_CONFIGURATION
- * USB_CFG_DESCR_PROPS_STRINGS
- * USB_CFG_DESCR_PROPS_STRING_0
- * USB_CFG_DESCR_PROPS_STRING_VENDOR
- * USB_CFG_DESCR_PROPS_STRING_PRODUCT
- * USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
- * USB_CFG_DESCR_PROPS_HID
- * USB_CFG_DESCR_PROPS_HID_REPORT
- * USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
- *
- * Note about string descriptors: String descriptors are not just strings, they
- * are Unicode strings prefixed with a 2 byte header. Example:
- * int serialNumberDescriptor[] = {
- * USB_STRING_DESCRIPTOR_HEADER(6),
- * 'S', 'e', 'r', 'i', 'a', 'l'
- * };
- */
-
-#define USB_CFG_DESCR_PROPS_DEVICE 0
-#define USB_CFG_DESCR_PROPS_CONFIGURATION 0
-#define USB_CFG_DESCR_PROPS_STRINGS 0
-#define USB_CFG_DESCR_PROPS_STRING_0 0
-#define USB_CFG_DESCR_PROPS_STRING_VENDOR 0
-#define USB_CFG_DESCR_PROPS_STRING_PRODUCT 0
-#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER 0
-#define USB_CFG_DESCR_PROPS_HID 0
-#define USB_CFG_DESCR_PROPS_HID_REPORT 0
-#define USB_CFG_DESCR_PROPS_UNKNOWN 0
-
-
-#define usbMsgPtr_t unsigned short
-/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
- * a scalar type here because gcc generates slightly shorter code for scalar
- * arithmetics than for pointer arithmetics. Remove this define for backward
- * type compatibility or define it to an 8 bit type if you use data in RAM only
- * and all RAM is below 256 bytes (tiny memory model in IAR CC).
- */
-
-/* ----------------------- Optional MCU Description ------------------------ */
-
-/* The following configurations have working defaults in usbdrv.h. You
- * usually don't need to set them explicitly. Only if you want to run
- * the driver on a device which is not yet supported or with a compiler
- * which is not fully supported (such as IAR C) or if you use a differnt
- * interrupt than INT0, you may have to define some of these.
- */
-/* #define USB_INTR_CFG MCUCR */
-/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
-/* #define USB_INTR_CFG_CLR 0 */
-/* #define USB_INTR_ENABLE GIMSK */
-/* #define USB_INTR_ENABLE_BIT INT0 */
-/* #define USB_INTR_PENDING GIFR */
-/* #define USB_INTR_PENDING_BIT INTF0 */
-/* #define USB_INTR_VECTOR INT0_vect */
-
-#endif /* __usbconfig_h_included__ */
diff --git a/usbdrv/usbconfig.2_.h b/usbdrv/usbconfig.2_.h
deleted file mode 100644
index ec38999..0000000
--- a/usbdrv/usbconfig.2_.h
+++ /dev/null
@@ -1,235 +0,0 @@
-#ifndef __usbconfig_h_included__
-#define __usbconfig_h_included__
-#define USB_CFG_IOPORTNAME D
-#define USB_CFG_DMINUS_BIT 3
-#define USB_CFG_DPLUS_BIT 2
-#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
-#define USB_CFG_CHECK_CRC 0
-#define USB_CFG_HAVE_INTRIN_ENDPOINT 0
-#define USB_CFG_HAVE_INTRIN_ENDPOINT3 0
-#define USB_CFG_EP3_NUMBER 3
-#define USB_CFG_IMPLEMENT_HALT 0
-#define USB_CFG_SUPPRESS_INTR_CODE 0
-#define USB_CFG_INTR_POLL_INTERVAL 10
-#define USB_CFG_IS_SELF_POWERED 0
-#define USB_CFG_MAX_BUS_POWER 50
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
-#define USB_CFG_IMPLEMENT_FN_WRITE 1
-/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
- * transfers. Set it to 0 if you don't need it and want to save a couple of
- * bytes.
- */
-#define USB_CFG_IMPLEMENT_FN_READ 0
-/* Set this to 1 if you need to send control replies which are generated
- * "on the fly" when usbFunctionRead() is called. If you only want to send
- * data from a static buffer, set it to 0 and return the data from
- * usbFunctionSetup(). This saves a couple of bytes.
- */
-#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
-/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
- * You must implement the function usbFunctionWriteOut() which receives all
- * interrupt/bulk data sent to any endpoint other than 0. The endpoint number
- * can be found in 'usbRxToken'.
- */
-#define USB_CFG_HAVE_FLOWCONTROL 0
-/* Define this to 1 if you want flowcontrol over USB data. See the definition
- * of the macros usbDisableAllRequests() and usbEnableAllRequests() in
- * usbdrv.h.
- */
-#define USB_CFG_DRIVER_FLASH_PAGE 0
-/* If the device has more than 64 kBytes of flash, define this to the 64 k page
- * where the driver's constants (descriptors) are located. Or in other words:
- * Define this to 1 for boot loaders on the ATMega128.
- */
-#define USB_CFG_LONG_TRANSFERS 0
-#define USB_COUNT_SOF 0
-#define USB_CFG_CHECK_DATA_TOGGLING 0
-/* define this macro to 1 if you want to filter out duplicate data packets
- * sent by the host. Duplicates occur only as a consequence of communication
- * errors, when the host does not receive an ACK. Please note that you need to
- * implement the filtering yourself in usbFunctionWriteOut() and
- * usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
- * for each control- and out-endpoint to check for duplicate packets.
- */
-#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
-/* define this macro to 1 if you want the function usbMeasureFrameLength()
- * compiled in. This function can be used to calibrate the AVR's RC oscillator.
- */
-#define USB_USE_FAST_CRC 0
-/* The assembler module has two implementations for the CRC algorithm. One is
- * faster, the other is smaller. This CRC routine is only used for transmitted
- * messages where timing is not critical. The faster routine needs 31 cycles
- * per byte while the smaller one needs 61 to 69 cycles. The faster routine
- * may be worth the 32 bytes bigger code size if you transmit lots of data and
- * run the AVR close to its limit.
- */
-
-/* -------------------------- Device Description --------------------------- */
-
-#define USB_CFG_VENDOR_ID 0xc0, 0x16 /* = 0x16c0 = 5824 = voti.nl */
-/* USB vendor ID for the device, low byte first. If you have registered your
- * own Vendor ID, define it here. Otherwise you may use one of obdev's free
- * shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
- * *** IMPORTANT NOTE ***
- * This template uses obdev's shared VID/PID pair for Vendor Class devices
- * with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
- * the implications!
- */
-#define USB_CFG_DEVICE_ID 0xdc, 0x05 /* = 0x05dc = 1500 */
-/* This is the ID of the product, low byte first. It is interpreted in the
- * scope of the vendor ID. If you have registered your own VID with usb.org
- * or if you have licensed a PID from somebody else, define it here. Otherwise
- * you may use one of obdev's free shared VID/PID pairs. See the file
- * USB-IDs-for-free.txt for details!
- * *** IMPORTANT NOTE ***
- * This template uses obdev's shared VID/PID pair for Vendor Class devices
- * with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
- * the implications!
- */
-#define USB_CFG_DEVICE_VERSION 0x00, 0x01
-/* Version number of the device: Minor number first, then major number.
- */
-#define USB_CFG_VENDOR_NAME 'w','i','n','d','f','i','s','c','h','.','o','r','g'
-#define USB_CFG_VENDOR_NAME_LEN 13
-/* These two values define the vendor name returned by the USB device. The name
- * must be given as a list of characters under single quotes. The characters
- * are interpreted as Unicode (UTF-16) entities.
- * If you don't want a vendor name string, undefine these macros.
- * ALWAYS define a vendor name containing your Internet domain name if you use
- * obdev's free shared VID/PID pair. See the file USB-IDs-for-free.txt for
- * details.
- */
-#define USB_CFG_DEVICE_NAME 'F','l','o',' ','T','e','s','t'
-#define USB_CFG_DEVICE_NAME_LEN 8
-/* Same as above for the device name. If you don't want a device name, undefine
- * the macros. See the file USB-IDs-for-free.txt before you assign a name if
- * you use a shared VID/PID.
- */
-/*#define USB_CFG_SERIAL_NUMBER 'N', 'o', 'n', 'e' */
-/*#define USB_CFG_SERIAL_NUMBER_LEN 0 */
-/* Same as above for the serial number. If you don't want a serial number,
- * undefine the macros.
- * It may be useful to provide the serial number through other means than at
- * compile time. See the section about descriptor properties below for how
- * to fine tune control over USB descriptors such as the string descriptor
- * for the serial number.
- */
-#define USB_CFG_DEVICE_CLASS 0xff /* set to 0 if deferred to interface */
-#define USB_CFG_DEVICE_SUBCLASS 0
-/* See USB specification if you want to conform to an existing device class.
- * Class 0xff is "vendor specific".
- */
-#define USB_CFG_INTERFACE_CLASS 0 /* define class here if not at device level */
-#define USB_CFG_INTERFACE_SUBCLASS 0
-#define USB_CFG_INTERFACE_PROTOCOL 0
-/* See USB specification if you want to conform to an existing device class or
- * protocol. The following classes must be set at interface level:
- * HID class is 3, no subclass and protocol required (but may be useful!)
- * CDC class is 2, use subclass 2 and protocol 1 for ACM
- */
-/* #define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 42 */
-/* Define this to the length of the HID report descriptor, if you implement
- * an HID device. Otherwise don't define it or define it to 0.
- * If you use this define, you must add a PROGMEM character array named
- * "usbHidReportDescriptor" to your code which contains the report descriptor.
- * Don't forget to keep the array and this define in sync!
- */
-
-/* #define USB_PUBLIC static */
-/* Use the define above if you #include usbdrv.c instead of linking against it.
- * This technique saves a couple of bytes in flash memory.
- */
-
-/* ------------------- Fine Control over USB Descriptors ------------------- */
-/* If you don't want to use the driver's default USB descriptors, you can
- * provide our own. These can be provided as (1) fixed length static data in
- * flash memory, (2) fixed length static data in RAM or (3) dynamically at
- * runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
- * information about this function.
- * Descriptor handling is configured through the descriptor's properties. If
- * no properties are defined or if they are 0, the default descriptor is used.
- * Possible properties are:
- * + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
- * at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
- * used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
- * you want RAM pointers.
- * + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
- * in static memory is in RAM, not in flash memory.
- * + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
- * the driver must know the descriptor's length. The descriptor itself is
- * found at the address of a well known identifier (see below).
- * List of static descriptor names (must be declared PROGMEM if in flash):
- * char usbDescriptorDevice[];
- * char usbDescriptorConfiguration[];
- * char usbDescriptorHidReport[];
- * char usbDescriptorString0[];
- * int usbDescriptorStringVendor[];
- * int usbDescriptorStringDevice[];
- * int usbDescriptorStringSerialNumber[];
- * Other descriptors can't be provided statically, they must be provided
- * dynamically at runtime.
- *
- * Descriptor properties are or-ed or added together, e.g.:
- * #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
- *
- * The following descriptors are defined:
- * USB_CFG_DESCR_PROPS_DEVICE
- * USB_CFG_DESCR_PROPS_CONFIGURATION
- * USB_CFG_DESCR_PROPS_STRINGS
- * USB_CFG_DESCR_PROPS_STRING_0
- * USB_CFG_DESCR_PROPS_STRING_VENDOR
- * USB_CFG_DESCR_PROPS_STRING_PRODUCT
- * USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
- * USB_CFG_DESCR_PROPS_HID
- * USB_CFG_DESCR_PROPS_HID_REPORT
- * USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
- *
- * Note about string descriptors: String descriptors are not just strings, they
- * are Unicode strings prefixed with a 2 byte header. Example:
- * int serialNumberDescriptor[] = {
- * USB_STRING_DESCRIPTOR_HEADER(6),
- * 'S', 'e', 'r', 'i', 'a', 'l'
- * };
- */
-
-#define USB_CFG_DESCR_PROPS_DEVICE 0
-#define USB_CFG_DESCR_PROPS_CONFIGURATION 0
-#define USB_CFG_DESCR_PROPS_STRINGS 0
-#define USB_CFG_DESCR_PROPS_STRING_0 0
-#define USB_CFG_DESCR_PROPS_STRING_VENDOR 0
-#define USB_CFG_DESCR_PROPS_STRING_PRODUCT 0
-#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER 0
-#define USB_CFG_DESCR_PROPS_HID 0
-#define USB_CFG_DESCR_PROPS_HID_REPORT 0
-#define USB_CFG_DESCR_PROPS_UNKNOWN 0
-
-
-#define usbMsgPtr_t unsigned short
-/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
- * a scalar type here because gcc generates slightly shorter code for scalar
- * arithmetics than for pointer arithmetics. Remove this define for backward
- * type compatibility or define it to an 8 bit type if you use data in RAM only
- * and all RAM is below 256 bytes (tiny memory model in IAR CC).
- */
-
-/* ----------------------- Optional MCU Description ------------------------ */
-
-/* The following configurations have working defaults in usbdrv.h. You
- * usually don't need to set them explicitly. Only if you want to run
- * the driver on a device which is not yet supported or with a compiler
- * which is not fully supported (such as IAR C) or if you use a differnt
- * interrupt than INT0, you may have to define some of these.
- */
-/* #define USB_INTR_CFG MCUCR */
-/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
-/* #define USB_INTR_CFG_CLR 0 */
-/* #define USB_INTR_ENABLE GIMSK */
-/* #define USB_INTR_ENABLE_BIT INT0 */
-/* #define USB_INTR_PENDING GIFR */
-/* #define USB_INTR_PENDING_BIT INTF0 */
-/* #define USB_INTR_VECTOR INT0_vect */
-
-#endif /* __usbconfig_h_included__ */
diff --git a/usbdrv/usbconfig.2__.h b/usbdrv/usbconfig.2__.h
deleted file mode 100644
index 458ca8d..0000000
--- a/usbdrv/usbconfig.2__.h
+++ /dev/null
@@ -1,49 +0,0 @@
-#ifndef __usbconfig_h_included__
-#define __usbconfig_h_included__
-#define USB_CFG_IOPORTNAME D
-#define USB_CFG_DMINUS_BIT 3
-#define USB_CFG_DPLUS_BIT 2
-#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
-#define USB_CFG_CHECK_CRC 0
-#define USB_CFG_HAVE_INTRIN_ENDPOINT 0
-#define USB_CFG_HAVE_INTRIN_ENDPOINT3 0
-#define USB_CFG_EP3_NUMBER 3
-#define USB_CFG_IMPLEMENT_HALT 0
-#define USB_CFG_SUPPRESS_INTR_CODE 0
-#define USB_CFG_INTR_POLL_INTERVAL 10
-#define USB_CFG_IS_SELF_POWERED 0
-#define USB_CFG_MAX_BUS_POWER 50
-#define USB_CFG_IMPLEMENT_FN_WRITE 1
-#define USB_CFG_IMPLEMENT_FN_READ 0
-#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
-#define USB_CFG_HAVE_FLOWCONTROL 0
-#define USB_CFG_DRIVER_FLASH_PAGE 0
-#define USB_CFG_LONG_TRANSFERS 0
-#define USB_COUNT_SOF 0
-#define USB_CFG_CHECK_DATA_TOGGLING 0
-#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
-#define USB_USE_FAST_CRC 0
-#define USB_CFG_VENDOR_ID 0xc0, 0x16 /* = 0x16c0 = 5824 = voti.nl */
-#define USB_CFG_DEVICE_ID 0xdc, 0x05 /* = 0x05dc = 1500 */
-#define USB_CFG_DEVICE_VERSION 0x00, 0x01
-#define USB_CFG_VENDOR_NAME 'w','i','n','d','f','i','s','c','h','.','o','r','g'
-#define USB_CFG_VENDOR_NAME_LEN 13
-#define USB_CFG_DEVICE_NAME 'F','l','o',' ','T','e','s','t'
-#define USB_CFG_DEVICE_NAME_LEN 8
-#define USB_CFG_DEVICE_CLASS 0xff /* set to 0 if deferred to interface */
-#define USB_CFG_DEVICE_SUBCLASS 0
-#define USB_CFG_INTERFACE_CLASS 0 /* define class here if not at device level */
-#define USB_CFG_INTERFACE_SUBCLASS 0
-#define USB_CFG_INTERFACE_PROTOCOL 0
-#define USB_CFG_DESCR_PROPS_DEVICE 0
-#define USB_CFG_DESCR_PROPS_CONFIGURATION 0
-#define USB_CFG_DESCR_PROPS_STRINGS 0
-#define USB_CFG_DESCR_PROPS_STRING_0 0
-#define USB_CFG_DESCR_PROPS_STRING_VENDOR 0
-#define USB_CFG_DESCR_PROPS_STRING_PRODUCT 0
-#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER 0
-#define USB_CFG_DESCR_PROPS_HID 0
-#define USB_CFG_DESCR_PROPS_HID_REPORT 0
-#define USB_CFG_DESCR_PROPS_UNKNOWN 0
-#define usbMsgPtr_t unsigned short
-#endif /* __usbconfig_h_included__ */
diff --git a/usbdrv/usbconfig_.h b/usbdrv/usbconfig_.h
deleted file mode 100644
index a4288ce..0000000
--- a/usbdrv/usbconfig_.h
+++ /dev/null
@@ -1,280 +0,0 @@
-/* Name: usbconfig.h
- * Project: AVR USB driver
- * Author: Christian Starkjohann
- * Creation Date: 2005-04-01
- * Tabsize: 4
- * Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
- * License: Proprietary, free under certain conditions. See Documentation.
- * This Revision: $Id: usbconfig-prototype.h 206 2006-06-23 19:02:30Z cs $
- */
-
-#ifndef __usbconfig_h_included__
-#define __usbconfig_h_included__
-
-/*
-General Description:
-This file is an example configuration (with inline documentation) for the USB
-driver. It configures AVR-USB for an ATMega8 with USB D+ connected to Port D
-bit 2 (which is also hardware interrupt 0) and USB D- to Port D bit 0. You may
-wire the lines to any other port, as long as D- is on bit 0 and D+ is also
-wired to INT0.
-To create your own usbconfig.h file, copy this file to the directory
-containing "usbdrv" (that is your project firmware source directory) and
-rename it to "usbconfig.h". Then edit it accordingly.
-*/
-
-/* ---------------------------- Hardware Config ---------------------------- */
-
-#if defined(CCCB_COMPATIBLE)
-
- #define USB_CFG_IOPORTNAME D
- #define USB_CFG_DMINUS_BIT 1
- #define USB_CFG_DPLUS_BIT 2
-
-#else
-
- #define USB_CFG_IOPORTNAME B
- #define USB_CFG_DMINUS_BIT 0
- #define USB_CFG_DPLUS_BIT 1
-
-#endif
-
-/* ----------------------- Optional Hardware Config ------------------------ */
-
-/* #define USB_CFG_PULLUP_IOPORTNAME D */
-/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
- * V+, you can connect and disconnect the device from firmware by calling
- * the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
- * This constant defines the port on which the pullup resistor is connected.
- */
-/* #define USB_CFG_PULLUP_BIT 4 */
-/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
- * above) where the 1.5k pullup resistor is connected. See description
- * above for details.
- */
-/* #define USB_BUFFER_SECTION ".bss" */
-/* The USB receive buffer (variable "usbRxBuf") with a length of 22 bytes
- * MUST NOT cross a 256 byte boundary. We have introduced this configuration
- * option to allow you to change the data segment where this buffer is
- * allocated. If you have problems with the default segment (start of .bss),
- * you may change this setting. See the comment in usbdrv.h for details.
- * On IAR C, the default is the TINY_Z segment (first 256 bytes). You must
- * change this default for devices which don't have RAM below 0x100.
- */
-
-/* --------------------------- Functional Range ---------------------------- */
-
-#ifndef BOOTLOADER
- #ifndef USB_HID
- #define USB_CFG_HAVE_INTRIN_ENDPOINT 1
-/* Define this to 1 if you want to compile a version with two endpoints: The
- * default control endpoint 0 and an interrupt-in endpoint 1.
- */
- #define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
-/* Define this and USB_CFG_HAVE_INTRIN_ENDPOINT to 1 if you want to compile a
- * version with three endpoints: The default control endpoint 0, an
- * interrupt-in endpoint 1 and an interrupt-in endpoint 3.
- */
- #else
- #define USB_CFG_HAVE_INTRIN_ENDPOINT 0
- #define USB_CFG_HAVE_INTRIN_ENDPOINT3 0
- #endif
-#else
- #define USB_CFG_HAVE_INTRIN_ENDPOINT 0
- #define USB_CFG_HAVE_INTRIN_ENDPOINT3 0
-#endif
-#define USB_CFG_IMPLEMENT_HALT 0
-/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
- * for endpoint 1 (interrupt endpoint). Although you may not need this feature,
- * it is required by the standard. We have made it a config option because it
- * bloats the code considerably.
- */
-#define USB_CFG_INTR_POLL_INTERVAL 10
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
-#define USB_CFG_IS_SELF_POWERED 0
-/* Define this to 1 if the device has its own power supply. Set it to 0 if the
- * device is powered from the USB bus.
- */
-#define USB_CFG_MAX_BUS_POWER 120
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
-#define USB_CFG_SAMPLE_EXACT 1
-/* This variable affects Sampling Jitter for USB receiving. When it is 0, the
- * driver guarantees a sampling window of 1/2 bit. The USB spec requires
- * that the receiver has at most 1/4 bit sampling window. The 1/2 bit window
- * should still work reliably enough because we work at low speed. If you want
- * to meet the spec, set this value to 1. This will unroll a loop which
- * results in bigger code size.
- * If you have problems with long cables, try setting this value to 1.
- */
-#define USB_CFG_IMPLEMENT_FN_WRITE 1
-/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
- * transfers. Set it to 0 if you don't need it and want to save a couple of
- * bytes.
- */
-#ifndef BOOTLOADER
- #define USB_CFG_IMPLEMENT_FN_READ 1
-/* Set this to 1 if you need to send control replies which are generated
- * "on the fly" when usbFunctionRead() is called. If you only want to send
- * data from a static buffer, set it to 0 and return the data from
- * usbFunctionSetup(). This saves a couple of bytes.
- */
-
- #ifndef USB_HID
- #define USB_CFG_IMPLEMENT_FN_WRITEOUT 1
- #else
- #define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
- #endif
-/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoint 1.
- * You must implement the function usbFunctionWriteOut() which receives all
- * interrupt/bulk data sent to endpoint 1.
- */
- #define USB_CFG_HAVE_FLOWCONTROL 1
-/* Define this to 1 if you want flowcontrol over USB data. See the definition
- * of the macros usbDisableAllRequests() and usbEnableAllRequests() in
- * usbdrv.h.
- */
-#else
- #define USB_CFG_IMPLEMENT_FN_READ 0
-#endif
-/* Define this to the size of your configuration descriptor if you provide
- * your own configuration descriptor at the global program memory address
- * 'usbDescrConfig'.
- */
-
-/* -------------------------- Device Description --------------------------- */
-
-#ifndef BOOTLOADER
- #ifndef ISAVRISPMKII
- #define USB_CFG_VENDOR_ID 0xc0, 0x16
-/* USB vendor ID for the device, low byte first. If you have registered your
- * own Vendor ID, define it here. Otherwise you use obdev's free shared
- * VID/PID pair. Be sure to read USBID-License.txt for rules!
- * This template uses obdev's shared VID/PID pair for HIDs: 0x16c0/0x5df.
- * Use this VID/PID pair ONLY if you understand the implications!
- */
- #ifndef USB_HID
- #define USB_CFG_DEVICE_ID 0xe1, 0x05
- #else
- #define USB_CFG_DEVICE_ID 0xdc, 0x05
- #endif
-/* This is the ID of the product, low byte first. It is interpreted in the
- * scope of the vendor ID. If you have registered your own VID with usb.org
- * or if you have licensed a PID from somebody else, define it here. Otherwise
- * you use obdev's free shared VID/PID pair. Be sure to read the rules in
- * USBID-License.txt!
- * This template uses obdev's shared VID/PID pair for HIDs: 0x16c0/0x5df.
- * Use this VID/PID pair ONLY if you understand the implications!
- */
- #else
- #define USB_CFG_VENDOR_ID 0x03, 0xeb
- #define USB_CFG_DEVICE_ID 0x21, 0x04
- #endif
-#endif
-#ifndef ISAVRISPMKII
- #define USB_CFG_DEVICE_VERSION 0x00, 0x01
-#else
- #define USB_CFG_DEVICE_VERSION 0x02, 0x00
-#endif
-/* Version number of the device: Minor number first, then major number.
- */
-#ifndef ISUSBASP
- #define USB_CFG_VENDOR_NAME 'w', 'i', 'n', 'd', 'f', 'i', 's', 'c', 'h', '.', 'o', 'r', 'g'
- #define USB_CFG_VENDOR_NAME_LEN 13
- #define USB_CFG_DEVICE_NAME 's', 'c', 'h', 'e', 'i', 'b', 'e'
- #define USB_CFG_DEVICE_NAME_LEN 7
-#else
- #define USB_CFG_VENDOR_NAME 'w', 'w', 'w', '.', 'f', 'i', 's', 'c', 'h', 'l', '.', 'd', 'e'
- #define USB_CFG_VENDOR_NAME_LEN 13
- #define USB_CFG_DEVICE_NAME 'U', 'S', 'B', 'a', 's', 'p'
- #define USB_CFG_DEVICE_NAME_LEN 6
-#endif
-
-/* Same as above for the device name. If you don't want a device name, undefine
- * the macros. See the file USBID-License.txt before you assign a name if you
- * use a shared VID/PID.
- */
-#define USB_CFG_SERIAL_NUMBER_LENGTH 0
-/* Set this define to the number of charcters in the serial number if your
- * device should have a serial number to uniquely identify each hardware
- * instance. You must supply the serial number in a string descriptor with the
- * name "usbCfgSerialNumberStringDescriptor", e.g.:
- * #define USB_CFG_SERIAL_NUMBER_LENGTH 5
- * int usbCfgSerialNumberStringDescriptor[] PROGMEM = {
- * USB_STRING_DESCRIPTOR_HEADER(USB_CFG_SERIAL_NUMBER_LENGTH),
- * '1', '2', '3', '4', '5'
- * };
- * See usbdrv.h for more information about the USB_STRING_DESCRIPTOR_HEADER()
- * macro or usbdrv.c for example string descriptors.
- * You may want to put "usbCfgSerialNumberStringDescriptor" at a constant
- * flash memory address (with magic linker commands) so that you don't need
- * to recompile if you change it.
- */
-#if defined(BOOTLOADER) || defined(USB_HID)
- #define USB_CFG_DEVICE_CLASS 0xff
- #define USB_CFG_DEVICE_SUBCLASS 0
-
- #define USB_CFG_INTERFACE_CLASS 0
- #define USB_CFG_INTERFACE_SUBCLASS 0
- #define USB_CFG_INTERFACE_PROTOCOL 0
-#else
- #define USB_CFG_DEVICE_CLASS 2
- #define USB_CFG_DEVICE_SUBCLASS 0
-/* See USB specification if you want to conform to an existing device class.
- */
- #ifndef ISAVRISPMKII
- #define USB_CFG_INTERFACE_CLASS 0x02 /* CDC class */
- #define USB_CFG_INTERFACE_SUBCLASS 2 /* Abstract (Modem) */
- #define USB_CFG_INTERFACE_PROTOCOL 1 /* AT-Commands */
- #else
- #define USB_CFG_INTERFACE_CLASS 0xff /* Vendor specific */
- #define USB_CFG_INTERFACE_SUBCLASS 0 /* none */
- #define USB_CFG_INTERFACE_PROTOCOL 0 /* none */
- #endif
-#endif
-#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0 /* total length of report descriptor */
-/* Define this to the length of the HID report descriptor, if you implement
- * an HID device. Otherwise don't define it or define it to 0.
- * Since this template defines a HID device, it must also specify a HID
- * report descriptor length. You must add a PROGMEM character array named
- * "usbHidReportDescriptor" to your code which contains the report descriptor.
- * Don't forget to keep the array and this define in sync!
- */
-
-/* ----------------------- Optional MCU Description ------------------------ */
-
-/* The following configurations have working defaults in usbdrv.h. You
- * usually don't need to set them explicitly. Only if you want to run
- * the driver on a device which is not yet supported or with a compiler
- * which is not fully supported (such as IAR C) or if you use a differnt
- * interrupt than INT0, you may have to define some of these.
- */
-/* #define USB_INTR_CFG MCUCR */
-/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
-/* #define USB_INTR_CFG_CLR 0 */
-/* #define USB_INTR_ENABLE GIMSK */
-/* #define USB_INTR_ENABLE_BIT INT0 */
-/* #define USB_INTR_PENDING GIFR */
-/* #define USB_INTR_PENDING_BIT INTF0 */
-
-#ifndef BOOTLOADER
- #ifndef USB_HID
- #define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
- #define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
- #define USB_CFG_DESCR_PROPS_STRINGS 0
- #define USB_CFG_DESCR_PROPS_STRING_0 0
- #define USB_CFG_DESCR_PROPS_STRING_VENDOR 0
- #define USB_CFG_DESCR_PROPS_STRING_PRODUCT 0
- #define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER 0
- #define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
- #define USB_CFG_DESCR_PROPS_HID_REPORT 0
- #define USB_CFG_DESCR_PROPS_UNKNOWN 0
- #endif
-#endif
-
-#endif /* __usbconfig_h_included__ */
diff --git a/usbdrv/usbconfig__.h b/usbdrv/usbconfig__.h
deleted file mode 100644
index 019b0b9..0000000
--- a/usbdrv/usbconfig__.h
+++ /dev/null
@@ -1,105 +0,0 @@
-#ifndef __usbconfig_h_included__
-#define __usbconfig_h_included__
-#if defined(CCCB_COMPATIBLE)
-#define USB_CFG_IOPORTNAME D
-#define USB_CFG_DMINUS_BIT 1
-#define USB_CFG_DPLUS_BIT 2
-#else
-#define USB_CFG_IOPORTNAME B
-#define USB_CFG_DMINUS_BIT 0
-#define USB_CFG_DPLUS_BIT 1
-#endif
-#ifndef BOOTLOADER
-#ifndef USB_HID
-#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
-#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
-#else
-#define USB_CFG_HAVE_INTRIN_ENDPOINT 0
-#define USB_CFG_HAVE_INTRIN_ENDPOINT3 0
-#endif
-#else
-#define USB_CFG_HAVE_INTRIN_ENDPOINT 0
-#define USB_CFG_HAVE_INTRIN_ENDPOINT3 0
-#endif
-#define USB_CFG_IMPLEMENT_HALT 0
-#define USB_CFG_INTR_POLL_INTERVAL 10
-#define USB_CFG_IS_SELF_POWERED 0
-#define USB_CFG_MAX_BUS_POWER 120
-#define USB_CFG_SAMPLE_EXACT 1
-#define USB_CFG_IMPLEMENT_FN_WRITE 1
-#ifndef BOOTLOADER
-#define USB_CFG_IMPLEMENT_FN_READ 1
-#ifndef USB_HID
-#define USB_CFG_IMPLEMENT_FN_WRITEOUT 1
-#else
-#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
-#endif
-#define USB_CFG_HAVE_FLOWCONTROL 1
-#else
-#define USB_CFG_IMPLEMENT_FN_READ 0
-#endif
-#ifndef BOOTLOADER
-#ifndef ISAVRISPMKII
-#define USB_CFG_VENDOR_ID 0xc0, 0x16
-#ifndef USB_HID
-#define USB_CFG_DEVICE_ID 0xe1, 0x05
-#else
-#define USB_CFG_DEVICE_ID 0xdc, 0x05
-#endif
-#else
-#define USB_CFG_VENDOR_ID 0x03, 0xeb
-#define USB_CFG_DEVICE_ID 0x21, 0x04
-#endif
-#endif
-#ifndef ISAVRISPMKII
-#define USB_CFG_DEVICE_VERSION 0x00, 0x01
-#else
-#define USB_CFG_DEVICE_VERSION 0x02, 0x00
-#endif
-#ifndef ISUSBASP
-#define USB_CFG_VENDOR_NAME 'w', 'i', 'n', 'd', 'f', 'i', 's', 'c', 'h', '.', 'o', 'r', 'g'
-#define USB_CFG_VENDOR_NAME_LEN 13
-#define USB_CFG_DEVICE_NAME 's', 'c', 'h', 'e', 'i', 'b', 'e'
-#define USB_CFG_DEVICE_NAME_LEN 7
-#else
-#define USB_CFG_VENDOR_NAME 'w', 'w', 'w', '.', 'f', 'i', 's', 'c', 'h', 'l', '.', 'd', 'e'
-#define USB_CFG_VENDOR_NAME_LEN 13
-#define USB_CFG_DEVICE_NAME 'U', 'S', 'B', 'a', 's', 'p'
-#define USB_CFG_DEVICE_NAME_LEN 6
-#endif
-#define USB_CFG_SERIAL_NUMBER_LENGTH 0
-#if defined(BOOTLOADER) || defined(USB_HID)
-#define USB_CFG_DEVICE_CLASS 0xff
-#define USB_CFG_DEVICE_SUBCLASS 0
-#define USB_CFG_INTERFACE_CLASS 0
-#define USB_CFG_INTERFACE_SUBCLASS 0
-#define USB_CFG_INTERFACE_PROTOCOL 0
-#else
-#define USB_CFG_DEVICE_CLASS 2
-#define USB_CFG_DEVICE_SUBCLASS 0
-#ifndef ISAVRISPMKII
-#define USB_CFG_INTERFACE_CLASS 0x02 /* CDC class */
-#define USB_CFG_INTERFACE_SUBCLASS 2 /* Abstract (Modem) */
-#define USB_CFG_INTERFACE_PROTOCOL 1 /* AT-Commands */
-#else
-#define USB_CFG_INTERFACE_CLASS 0xff /* Vendor specific */
-#define USB_CFG_INTERFACE_SUBCLASS 0 /* none */
-#define USB_CFG_INTERFACE_PROTOCOL 0 /* none */
-#endif
-#endif
-#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0 /* total length of report descriptor */
-#ifndef BOOTLOADER
-#ifndef USB_HID
-#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
-#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
-#define USB_CFG_DESCR_PROPS_STRINGS 0
-#define USB_CFG_DESCR_PROPS_STRING_0 0
-#define USB_CFG_DESCR_PROPS_STRING_VENDOR 0
-#define USB_CFG_DESCR_PROPS_STRING_PRODUCT 0
-#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER 0
-#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
-#define USB_CFG_DESCR_PROPS_HID_REPORT 0
-#define USB_CFG_DESCR_PROPS_UNKNOWN 0
-#endif
-#endif
-#endif /* __usbconfig_h_included__ */
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-22 08:56:03 +0000